Heavy duty protection for driving shafts including fitting key.
Speed-Fit. Single Push-Fit application and accurate fitting.
The Original. Up to 64.". One piece construction. Over 170 sizes.
Low-cost. Popular general-purpose plug. Over 150 sizes available.
Low-cost. Can be used as cap or a plug. Easy fitting and removal.
Low-cost. Can be used as cap or plug. Easy fitting and removal.
Easy removal. Protects threads, pipes, hoses and bores.
Large cover flange. Greater surface protection and easy removal.
Large cover flange and tab for easy removal. Push fit application.
Provides cushioned protection for DIN2402 flange face. DN10 - DN400.
Provides cushioned protection for flange face. DIN 2631-2635.
Suitable for ASA/ANSI/BS1560 flanges. Quick fitting. 150 lbs.
Suitable for ASA/ANSI/BS1560 flanges. Quick fitting. 300 lbs.
The Original. The most universal Push-In Protectors in the market.
Protect DIN and ANSI flanges. Guard the flange face DN 15 - DN 300.
The Original. Easy to install full flange-face protection.
Low-cost, quick fitting plugs suitable for most applications.
Large Pull Tab allows easy removal. Flexible rib design.
Low-cost, quick fitting plugs suitable for most applications.
Single turn gives tight fit once pushed into position.
Single turn. With flexible fins. Each plug covers a wide range of threads.
Handy pull-tab for easy removal. Temperature resistant up to 120 °C.
Designed to protect DKO fittings. Side-tab for quick removal.
Continuous sealing lip. Fit threaded or plain ports. Quick removal.
Knurled head and screwdriver slot allow easy installation and removal.
Flangeless. Specially designed for BSP thread sizes. Up to + 180 °C.
Designed to protect unified / straight threaded ports. Wide range.
Designed to perfectly seal internal threads to avoid fluid leakage.
Strong Nylon PA 6, integral tight fit sealing lip. Five complete threads.
Outstanding seal force useable under complicated conditions.
EP 436 body design. Head designed to drain leakage.
Threaded sealing plug design EP 435 complete with O-Ring.
EP 436 body design with factory-made fitting of an sealing O-Ring.
Special head design allows all fluids to drain off. Five complete threads.
Produced in hard polyethylene and designed with an easy to grip head.
Internal neoprene rubber sealing disk to limit fluid leakage.
Protects threaded components from dust, moisture and damage.
Effective protection against dirt, weathering and damage.
Snap-on installation. Anti-vibration locking lip. 175 Designs and Sizes.
For bolted joints without washers. From SW 10 to SW 130
For bolted joints with washers. With anti-vibration locking lip.
For bolted joints without washers. Adjustable for large bolt length.
For bolted joints with washers. Adjustable for large bolt length.
For quick-fit installation and extreme mechanical demands.
Improved level of safety against damaged cables and cores.
For secure tightening of cable glands and accessories.
For secure tightening of cable glands and accessories.
Close existing threads to secure unused ports for future use.
Ingress Rating IP 54. With piercing membrane.
Ingress Rating IP 54. With open membrane.
To allow multiple cables to enter into a single cable gland.
Nylon Reducers with large external thread and small internal thread.
Alters the threaded entry diameter on any threaded connector.
Nylon Enlargers with small external thread and large internal thread.
Heat resistant, Snap-In design enables quick and easy installation
Snap-In design enables quick and easy installation.
Easy-to-install. Wide clamping range. Twisting protection.
Rapid EMC connection of the cable shield. Built-in twisting protection.
Metric and PG. Secure tightening of glands and accessories.
With cutting edges to cut through paint or powder coatings.
Available for both metric to metric and PG to PG-threads.
Close existing threads to secure unused ports for future use.
Available for both metric to metric and PG to PG-threads.
Adapt from external metric to internal PG ports and vice versa.
Best Flange Protection during Sandblasting and Painting.
For installation over flange joints. Up to DN 600 and ANSI 24." 600.
Int. Patent. Designed for installation over welding neck flange joints.
Threaded caps - Flanged - With sealing disk
Tapered plugs with pull ring tab
Push-in flange face protectors
Sandblasting flange push-in plugs, Nylon PA
PROTEC meets the most stringent demands of safety and operations reliability. International approvals and certifications such as UL, CSA, VDE, VDA 6.1 and DIN EN ISO 9001: 2015 demonstrate total quality commitment on superior level.
Stay on top of the latest news and upcoming events and event information from PROTEC and its partner. Be the first to know when new products are on the market. Get periodic specials and news delivered directly to your email inbox! You can un-subscribe anytime.
Sign our free newsletter now
